IC 7300 menu setup

Table of Contents

• IC 7300 menu setup
  • Restore xcvr parameters
  • Select the Poll tab

IC 7300 menu setup

Press the transceiver MENU button then the on screen items: Set , then Connectors.

Make sure the settings for these items are as follows:

• USB SEND - Off
• USB Serial function - CI-V
• Data Mod - USB
• Data Off Mod - Mic, ACC or just Mic if you wish. This applies only when the rig is not in data mode.
• USB MOD Level - I have mine set at 28% so you might try this for starters. This is the input level control for the TX sound from the computer. How to fine tune it will be explained later.
• ACC/USB AF Beep/Speech level - Off
• ACC/USB AF SQL - Off
• ACC/USB AF Output level - I have mine set at 80%. This is the built-in soundcard in the radio output level that goes into fldigi on receive. Too much and you overdrive fldigi and decoding suffers, too little and you may miss weak signals though fldigi does very well with very weak signals. Something to play with to make it work best for you. See the fldigi manual on setting up the sound levels.
• ACC/USB Output Select - AF

Once the above are set then touch the CI-V line on screen to get a list of items to set especially for CAT control. Many of these are ok at default, but verify the ones listed below:

• CI-V address - 94h
• CI-V Transceive - Off
• CI-V USB Port - Unlink from REMOTE
• CI-V USB Baud Rate - 19,200. I use 115,200, but use 19,200 for starters as that is what flrig defaults to. Response will be a bit quicker with higher rates, but it will do well at 19,200 also.
• CI-V USB Echo Back – On. On is only needed for compatability with other software. Flrig does not need it on so if only using flrig then set to Off.

flrig setup

You should have already installed the driver for the built-in sound card in the 7300.

Connect the transceiver to the computer with a USB A-Male to B-Male cable and turn on the radio.

Install flrig.

For Windows flrig will install to it's own folders and should be installed in the normal application folder where other applications are installed.
Putting them in other folders can causes permissions issues sometimes on Windows 10. For Mac and Linux install them as you would any other application.

With the radio on and the USB cable connected and no other communications program running, Start flrig.

It will come up with just a basic display.

Initial Flrig Dialog

Go to the menu Config/Setup/Transceiver.

Select IC7300

Choose the 7300 from the Rig dropdown list. That will select the default settings which will be good for starters. Note: The RTS +12v and DTR +12v boxes do not need to be selected.

Select the Serial Port to use

• Windows - select the correct COM port
• Mac/Linux - Select the SilconLabs driver from the dropdown list.

If the device does not appear in the list then click the SerPort button to repopulate the list. It if still isn't in the list then the driver is not loading for some reason like the radio is not on or connected or the driver has not been installed properly so that needs to be rectified before going on. If you're using MacOS High Sierra or a later version of MacOS you may need to authorize the driver install in Security & Privacy setup in System Preferences after runing the install program. There will be a message on the General page if it has been blocked. Windows

Open the device manager and determine to which com port the serial driver from Silcon Labs is assigned and choose that from the drop down list. Verify that the Baud rate in flrig matches the baud rate selected in the rig. It's better to choose a fixed baud rate than Auto. Now, click the Init button. It should go from red to black lettering. If it does not go to black lettering then verify all of the above again, especially baud rate.

Restore xcvr parameters

Select the restore tab

Restore IC7300 Settings

and choose whether you want flrig to save and restore all the radio’s parameters on startup and exit or whether you want it to open with the same settings as the rig is currently using. If Use xcvr data is checked flrig will start up with the same settings as the rig currently is using.

Select the Poll tab

IC7300 Polling Settings

and select to poll all of the parameters.

Flrig now should have control of the rig so changing frequency in flrig will changed the frequency on the rig and visa versa. The buttons and sliders should do as they are labeled.

IC7300 Main Dialog

I would recommend before you move on that you go to the Config/UI menu and select Tooltips. They are a great help to the new user to figure out what each control does as not all are labeled. You can choose 4 different UI’s from the narrow one with small sliders (I use this one – see above screen shot of flrig), to a narrow one with large sliders, to a wide version or a touch version. Now close flrig and restart it to be sure all is well . Everything should be working and you should be able to change frequency on the radio and flrig should follow.

Page Top

Return to Contents